
Manufacturer Part #
DT04-3P
DT Series Contact Size 16 3 Way Gray Receptacle Housing
TE Connectivity DT04-3P - Product Specification
Shipping Information:
ECCN:
PCN Information:
General Product Description: DT 2 to 12 ways series connector Description of Changes The ICT business unit of TE is adding a fourth source material for the part numbers listed below. These PNs are TE proprietary designs, therefore considered catalog/general market product. PPAP and/or sample requests must be submitted within 14 days of PCN submission via ict-ppap-request@te.com or ePPAP system. Submission will not occur without request. If PPAP requested, disposition response is required within 14 days of submit date or it will be considered approved. Product drawings are not affected. Reason for Changes: Dear Customer, we hereby inform you of this change. The change is needed as a result of global demand in excess of PA66 and the available capacity of our suppliers. The additional source material does not impact performance. IMPORTANT: The current and previous revisions of these parts can be used interchangeably in the field. The change(s) are being phased in gradually and previous revision can remain stocked until use. Shipments of both configurations may be mixed. Product Category:ConnectorsChange Feature: Dual SourceKind of Change: MaterialPotential Customer Impact: No Customer ImpactFirst Ship Date of Changed Items (Changed Parts Only): 29-JUL-2022Last Date for Mixed Shipments: (Changed Parts Only): 30-JUN-2024
Description of Changes:The Industrial and Commercial Transportation business unit of TE Connectivity is adding an additional capacity assembly line for the TE part numbers listed below. These are a TE proprietary design, therefore considered catalog/general market product. PPAP and/or sample requests must be submitted within 14 days of PCN submission via ict-ppap-request@te.com or ePPAP system. Submission will not occur without request. If PPAP requested, disposition response is required within 14 days of submit date or it will be considered approved. Product drawing is not affected
General Product Description: DT 2 to 12 pin series connectors. The ICT business unit of TEC is releasing a 3rd source material for the part numbers Description of Changes DT 2 to 12 pin series connectors. The ICT business unit of TEC is releasing a 3rd source material for the part numbers listed, effectively immediately. We previously shared PCN -21-112194 that indicated we were adding a third source of PA66 materiial.Product Category: Connector HousingsFirst Ship Date of Changed Items (Changed Parts Only): 18-NOV-2021
General Product Description: DT 2 to 12 ways series connector Description of Changes The ICT business unit of TE is adding a third source material for the part numbers listed. These PNs are TE proprietary designs, therefore considered catalog/general market product. PPAP and/or sample requests must be submitted within 14 days of PCN submission via ict-ppap-request@te.com or ePPAP system. Submission will not occur without request. If PPAP requested, disposition response is required within 14 days of submit date or it will be considered approved. Product drawings are not affected. Reason for Changes: Dear Customer, we hereby inform you of this change. The change is needed as a result of global demand in excess of PA66 and the available capacity of our suppliers. The 3rd source material does not impact performance. IMPORTANT: The current and previous revisions of these parts can be used interchangeably in the field. The change(s) are being phased in gradually and previous revision can remain stocked until use. Shipments of both configurations may be mixed. First Date To Ship (Changed Parts Only): 22-DEC-2021Last Date for Mixed Shipments: (Changed Parts Only): 22-JUN-2023
Description of Changes The Industrial and Commercial Transportation business unit of TE Connectivity is upgrading the automated assembly machines for the part number(s) listed. The new equipment s laser will improve the legibility on the cavity ID marking. The affected parts packaging will change to the standard automotive AIAG shape and size boxes with dimensions LxWxH 15.375x9.5x8.563 inches. Standard Package Quantity will not change. Product drawings are not affected. These PNs are TE proprietary designs, therefore considered catalog/general market product. PPAP and/or sample requests must be submitted within 14 days of PCN submission via ict-ppap-request@te.com or ePPAP system. Submission will not occur without request.Reason for Changes: Dear Customer, we hereby inform you of this change. The change is necessary to improve the operating efficiency and to standardize packaging in the current manufacturing location. The change does not impact connector performance. IMPORTANT: The current and previous revisions of these parts can be used interchangeably in the field. The change(s) are being phased in gradually and previous revision can remain stocked until use.
General Product Description: DT 2/3 ways series connector Description of Changes The ICT business unit of TE is adding a 2nd source material for the part numbers listed below. Currently the DT connectors are using single source PA66 material. The 2nd source material does not impact performance. The 2nd source material is V0 and UL re-certification on the connectors is in process. These PNs are TE proprietary designs, therefore considered catalog/general market product. PPAP and/or sample requests must be submitted within 14 days of PCN submission via ict-ppap-request@te.com or ePPAP system. Submission will not occur without request. If PPAP requested, disposition response is required within 14 days of submit date or it will be considered approved. Product drawings are not affected. Shipments of both configurations may be mixed. Reason for Changes: Dear Customer, we hereby inform you of this change. With global demand in excess of supply on PA66 the material supplier is restricting TE buying allotment. The allotted amount is at a level where production is impacted and to close the gap an alternative PA66 supply is needed. IMPORTANT: The current and previous revisions of these parts can be used interchangeably in the field. The change is being phased in gradually and previous revision can remain stocked until use. First Date To Ship (Changed Parts Only): 15-JUN-2021Last Date for Mixed Shipments: (Changed Parts Only): 15-DEC-2022
General Product Description: DEUTSCH DT Series Connectors Additional Production Manufacturing Location Description of Changes The Industrial and Commercial Transportation business unit of TE Connectivity is adding new assembly lines for the following part number(s) in Tecate, BC, MX. These PNs are TE proprietary designs, therefore considered catalog/general market product. A Level IV PPAP and/or sample requests must be submitted within 14 days of PCN submission via ict-ppap-request@te.com or ePPAP system. Submission will not occur without request. If PPAP requested, disposition response is required within 14 days of submit date or it will be considered approved. Product drawings are not affected. Reason for Changes: Dear Customer, we hereby inform you of this change. The new assembly lines are necessary to better meet our Customers demand needs. The additional lines will not impact connector performance. IMPORTANT: There is no impact to fit, form or function. Parts off the new lines are identical to current production. Shipments may be mixed. First Date To Ship (Changed Parts Only): 11-JUN-2021Last Date for Mixed Shipments: (Changed Parts Only): 11-DEC-2022
TE Industrial & Commercial Transportation Solutions Force Majeure Notice - Resin Supply TE Connectivity and its affiliates (collectively TE) have received Force Majeure notices from several resin suppliers (including Almaak, Ascend, BASF, DOMO, DuPont, Lanxess, LyondellBasell, Sabic and Solvay) with the potential for more to be added to the list. Please be assured that TE is exploring options to minimize the impact to your supply chain. Specifically, TE is (1) continuously working to learn our suppliers' resulting allocation decisions and determine how those allocation decisions are going to impact our production; and (2) where possible, actively testing alternative material procured from an alternative supply source. Please be prepared that we may approach you for urgent decision making in this regard. However, due to the unprecedented supply challenges and raw material shortages, TE must respectfully advise that these circumstances (i) render TE's performance impossible, and (ii) constitute a Force Majeure event under all applicable agreements between TE and its customers and their respective affiliates. As such, TE will not accept responsibility (including the responsibility for financial costs) for any resulting line-down or other supply chain related charges.
DEUTSCH DT Series Plug and Receptacle E-seal Grommet Color Change Description of Changes The Industrial and Commercial Transportation (ICT) business unit of TE Connectivity (TEC) is making a change to the product drawing for E-Seal grommet Grommet (E-Seal) color change from "Red-Orange" to "Burnt Red". 114-151009 Spec has been updated. Reason for Changes: The change is necessary to help our manual assembly lines to make a visual distinction between E-seal and N-seal grommets. This change affects form only (grommet color). The change does not impact performance. IMPORTANT: The current and previous revisions of these parts can be used interchangeably in the field. The change(s) are being phased in gradually and previous revision can remain stocked until use. Shipments of both configurations may be mixed
Description of Changes:The ICT business unit of TE Connectivity is transferring production of part numbers listed in this notice from TE Hemet/CA-USA to TE Tullahoma/TN-USA, TE Empalme/Mexico, or TE externally approved supplier. Shipping point will change from Ontario, CA, USA to Greensboro, NC, USA or Hermosillo, Mexico. These PNs are TE proprietary designs, therefore considered catalog/general market product. Tools that manufacture parts within this PCN are identified as "swing tool" and TE reserves the right in future to move tool to a TE ICT Manufacturing location and/or a TE externally approved supplier as needed. In case of subsequent transfer of swing tool, PCN will be sent to notify with zero day wait period. PPAP and/or sample requests must be submitted within 14 days of PCN submission via ict-ppap-request@te.com or TE e-PPAP system. Reason for Changes: This change is necessary for alignment of overall manufacturing capacity and footprint to better meet our Customer's needs. IMPORTANT: The change will not impact fit, form or function
Part Status:
TE Connectivity DT04-3P - Technical Attributes
Type: | Contact |
Contact Termination: | Crimp Terminal |
No of Positions: | 3 |
Color: | Grey |
Mounting Method: | Wire Mount |
Available Packaging
Package Qty:
1 per Bag
Mounting Method:
Wire Mount